Watersports

General mintenance kit for repairing all types of outdoor clothing and footwear.

This unique repair kit comes in a very convnient bag with clip, perfect for outdoor expditions.

This selection of very special adhesive glue, tape, oil and shampoo are one of the few products that can repair leaks, cracks and rips on all coats, trousers, gloves, hats, suits, goggles, glasses, boots, shoes and trainers and many more!
Repairs are permanent, strong, waterproof, flexible and resistant to abrasion (weather and water abrasion).

You don't need to buy new, repair your favourite items with this selection Stormsure products. You can plug the hole or patch the tear or clean materials with this excellent product.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS:
Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.
TIPS:
Mix with Stormcure Accelerator to reduce cure time to approximately 1 hour. Ensure there is no air left in the tube before replacing cap.
Store partly-used tubes in a deep freezer.

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This nifty adhesive will enable you to make easy and durable repairs to rips, roles, leaks and split seams on wetsuit and drysuit material. 

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 5 minutes, it should be touch dry and you will be ready to go back in the water!

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual water sports enthusiasts as well as professional triathletes who want to stand out.

It's all about Stormsure Flexible Repair Adhesive

How to Repair using Polyurethane Adhesive

Stormsure Flexible Repair Adhesive is a polyurethane based adhesive and can be used in situations that demand extremely high durability, strength and flexibility. The degree of elasticity offered allows for use for both static as well as for more flexible bonding and sealing purposes. These adhesive types are formulated from polymers and solvents.

• Stormsure can be used as either an adhesive to join two surfaces together, or as a surface sealant when spread over just one surface.
• Bonds to virtually all surfaces. It allows bonding wood, concrete, stone, metals, laminate, plastics, glass, PU, and most flexible natural and man made fabrics on themselves or in combination. It can also be used to glue models, flexible fabrics, inflatable items, waterproof items, brickwork, joinery and a huge range of other things too.
• Stormsure is a liquid clear polyurethane-based (PU) adhesive that has been specifically developed to provide strong and reliable bonding to a wide range of materials
• Stormsure is a one-part polyurethane adhesive that reacts with moisture to polymerize and cure which provides very strong and waterproof bonding. It is suitable for indoor and outdoor use.
• The glue is transparent so it won't normally discolour the objects you need to join.
• Always check for compatibility on fabrics in an inconsipcuous area before making a major repair. It is used for repairs and construction where a very high connection strength is required. It can be used indoors and outdoors and will last for a long time under water too.
• Complete curing time: 10-12 hours. Resistent to temperatures from -30°C to +80°C.
• How to use: Surfaces to be bonded must be clean and free of dirt (dust, grease, etc.). Apply glue to one of the surfaces to be bonded. Assemble immediately. Press strongly and immobilize for at least 10-12 hours.
• TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before re-use. Cured clear adhesive may change to a pale yellow colour when exposed to bright light.

The Science

In the case of Stormsure adhesive – the liquid glue will start to cure when it is exposed to even the smallest amount of water vapour in the air. This initiates a chemical chain reaction which will continue until all the glue has cured. The glue should be used at room temperature (15°C - 25°C for best results). Do not use below 5°C.  If the glue is too cold the it may appear white and waxy. - Just warm it up until it is a transparent liquid again and it will work fine. 

This adhesive is a single component moisture curing product.  It has 70% solids content and will only shrink slightly as it cures but this helps to create a very strong and tight bond on most surfaces. It can be used to fill gaps and holes.

What is it used for?

Stormsure adhesive is incredibly versatile, making it a good choice for those needing an all-purpose adhesive that is flexible and durable. Stormsure can be used to bond leather, tile, rubber, PVC, wood, concrete, stone, metals, laminate, most plastics glass and PU on themselves or in combination. It can also be used to glue models, joinery, door sills, stairs, skirting boards, window sills.

Other Characteristics

It also offers complete water resistance and allows sanding and painting when it has dried completely. Polyurethane glue can also fill and even out inconsistencies in the surface you use it on. Characteristics like these, and numerous others, make this type of adhesive an essential tool that is well suited for a wide range of bonding applications.

• Stormsure Flexible Repair Adhesive is a liquid clear polyurethane-based (PU) adhesive that has been specifically developed to provide strong and reliable bonding to a wide range of materials.
• Stormsure Flexible Repair Adhesive is a one-part polyurethane adhesive that reacts with moisture to polymerize and cure which provides very strong, flexible and waterproof bonding.
• Comes in White, Clear, Khaki and Black. It is used for repairs and constructions where a very high connection strength is required and can be used indoors, outdoors and gor repairs that will be under water..
• This glue increases its volume when curing allowing it to fill irregularities. It is resistant to humidity (Class D4), shock and vibrations and temperature variations.

How To Use Stormsure

Surfaces to be bonded must be clean and free of dirt (dust, mud, grease, etc.). You can use an alcohol wipe to clean the surfaces, if not, then just soap and water will do. Be sure the surfaces are dry before application. Apply the glue to one of the surfaces to be bonded. To ensure the best result, at least one of the surfaces must be porous or permeable. Thus, it is recommended to sand/roughen smooth surfaces. Assemble immediately. Press strongly and immobilize for at least 24 hours.

Conclusion

Despite the marginally higher cost of polyurethane adhesives, they do offer plenty of worthwhile benefits. They are well suited for use with a variety of different materials, and their strong adhesion allows single-sided application. Polyurethane adhesives are easy to work with. Polyurethane adhesives are also highly resistant to the elements and can endure heavy contact and impact.

Neoprene Adhesive contact cement is suitable for quick repairs (5-10mins) to Neoprene, rubber, latex and vinyl. Repairs rips and tears and is also suitable for butt end joining of seams or edges where the rubber directly bonds together.

Neoprene Adhesive will fix that hole in your raft, fix the tear in your fishing waders or wetsuit and make sure you stay dry.

• Strong

• Flexible and Durable

• Abrasion resistant

• Waterproof

• Suitable for most materials 

or quick, grab-and-hold repairs in the field, opt for Neoprene-based Adhesive contact cement. Contact cements are formulated specifically for quick bonding. Cures in 5-10mins.

P.U. Glue is a liquid clear polyurethane-based (PU) adhesive that has been specifically developed to provide strong and reliable bonding to a wide range of materials. 

P.U. Glue is a one-part polyurethane adhesive that reacts with moisture to polymerize and cure which provides very strong and waterproof bonding.

The glue is transparent so it won't discolour the objects you need to join. It is used for repairs and constructions where a very high connection strength is required and can be used indoors and outdoors.

This glue increases its volume when curing allowing it to fill irregularities. It is resistant to humidity (Class D4), shock and vibrations and temperature variations.

• Flexible and durable
• Fills gaps and cracks
• Excellent balance of flexibility and high strength
• Waterproof
• High cohesive strength
• Abrasion resistance
• Impact resistance
• Extremely tough

It allows bonding wood, concrete, stone, metals, laminate, plastic, glass, PU, polystyrene on themselves or in combination. It can also be used to glue models, joinery, door sills, stairs, skirting boards, window sills.

Complete curing time: 24 hours.

Resistent to temperatures from -30°C to +80°C.

To ensure the best result, at least one of the surfaces must be porous or permeable. Thus, it is recommended to sand/roughen smooth surfaces.

How to use: Surfaces to be bonded must be free of dirt (dust, grease, etc.) as much as possible. Apply glue to one of the surfaces to be bonded. Assemble immediately. Press strongly and immobilize for at least 10-12 hours.

P.U. Glue is a liquid clear polyurethane-based (PU) adhesive that has been specifically developed to provide strong and reliable bonding to a wide range of materials. 

P.U. Glue is a one-part polyurethane adhesive that reacts with moisture to polymerize and cure which provides very strong and waterproof bonding.

The glue is transparent so it won't discolour the objects you need to join. It is used for repairs and constructions where a very high connection strength is required and can be used indoors and outdoors.

This glue increases its volume when curing allowing it to fill irregularities. It is resistant to humidity (Class D4), shock and vibrations and temperature variations.

• Flexible and durable
• Fills gaps and cracks
• Excellent balance of flexibility and high strength
• Waterproof
• High cohesive strength
• Abrasion resistance
• Impact resistance
• Extremely tough

It allows bonding wood, concrete, stone, metals, laminate, plastic, glass, PU, polystyrene on themselves or in combination. It can also be used to glue models, joinery, door sills, stairs, skirting boards, window sills.

Complete curing time: 24 hours.

Resistent to temperatures from -30°C to +80°C.

To ensure the best result, at least one of the surfaces must be porous or permeable. Thus, it is recommended to sand/roughen smooth surfaces.

How to use: Surfaces to be bonded must be free of dirt (dust, grease, etc.) as much as possible. Apply glue to one of the surfaces to be bonded. Assemble immediately. Press strongly and immobilize for at least 10-12 hours.

P.U. Glue is a liquid clear polyurethane-based (PU) adhesive that has been specifically developed to provide strong and reliable bonding to a wide range of materials. 

P.U. Glue is a one-part polyurethane adhesive that reacts with moisture to polymerize and cure which provides very strong and waterproof bonding.

The glue is transparent so it won't discolour the objects you need to join. It is used for repairs and constructions where a very high connection strength is required and can be used indoors and outdoors.

This glue increases its volume when curing allowing it to fill irregularities. It is resistant to humidity (Class D4), shock and vibrations and temperature variations.

• Flexible and durable
• Fills gaps and cracks
• Excellent balance of flexibility and high strength
• Waterproof
• High cohesive strength
• Abrasion resistance
• Impact resistance
• Extremely tough

It allows bonding wood, concrete, stone, metals, laminate, plastic, glass, PU, polystyrene on themselves or in combination. It can also be used to glue models, joinery, door sills, stairs, skirting boards, window sills.

Complete curing time: 24 hours.

Resistent to temperatures from -30°C to +80°C.

To ensure the best result, at least one of the surfaces must be porous or permeable. Thus, it is recommended to sand/roughen smooth surfaces.

How to use: Surfaces to be bonded must be free of dirt (dust, grease, etc.) as much as possible. Apply glue to one of the surfaces to be bonded. Assemble immediately. Press strongly and immobilize for at least 10-12 hours.

What is Silicone?

• Stormsure Silicone is a Non-Staining No Oily Residue Silicone Adhesive and Sealant (Not all silicone adhesives are non-staining).

• Highly water repellent

• Highly resistant to weathering and ageing

• Electrically insulating Environmentally friendly, both in its production and in its application

• Resistant to many acids and other chemicals

Using silicone as a seam sealer: This type of sealer is ideal for outdoor gear and clothing made from synthetic materials. It's waterproof and flexible, making it ideal for sealing seams exposed to rain and other elements.

It is also ideal for sealing brickwork, tiles, slabs and concrete.

Advantages and Disadvantages of Silicone-Based Adhesives

A silicone rubber adhesive offers the user many different advantages:

PROS

• Temperature-resistant in a range from -85° to 572° Fahrenheit (-65° to 300° Celsius).

• Suitable for outdoor and indoor use

• Waterproof

• High UV and weathering resistance

• Highly elastic, making it suitable for bonding materials with different coefficients of thermal expansion, as well as for bonding vibrating parts Electrical non-conductor

CONS

Cannot withstand very high vibrations and strong movement loads in the long term due to its elasticity

One-component silicone adhesives generally not suitable for high-strength bonding that must withstand large loads on a permanent basis – over time, the silicone may wear and come loose

Cannot be painted over Produce an unpleasant odour of vinegar during curing phase

What is it used for?

The areas of application for silicone adhesives are diverse. For example, materials can be reliably bonded together, especially outdoors, where the adhesive seam must be weather-resistant and waterproof. Bonding and attaching tiles is also no problem with a silicone rubber adhesive. The following materials are reliably bonded with silicone-based glues:

• Outdoor gear and clothing made from synthetic materials

• Sealing seams exposed to rain and other elements

• Wood

• Glass

• Various plastics

• Metal

• Ceramics

• Enamel

• Paper and cardboard

• Brickwork, tiles, slabs, concrete

• Bathroom and kitchen sealant

Many users place particular emphasis on the ease of processing and flexibility of silicone, which is ideal for bonding substrates that are permanently exposed to vibrations or temperature fluctuations, such as:

• Parts on automobiles

• Fastening of illuminant parts

• Computer components

• Kitchen parts, for example on ovens or other electrical appliances

Preparation

Before you can bond the silicone, you must clean the substrates thoroughly. These must be free of any dirt, dust, oil, and grease. Any old grout must also be removed before you can bond new tiles with silicone, for example. The tiles to be laid or the other substrates can be cleaned with by rinsing it with water, but also with isopropanol or acetone.

Allow the surfaces to dry completely before starting the silicone bonding process. If the substrates show very uneven areas, these must still be filled or the surrounding raised areas must be ground down. Silicone is not suitable for bridging large gaps during the bonding process.

The Bonding Process

Before you apply the silicone adhesive to the actual substrates, it is recommended that you practice on a piece of cardboard. If the handling works well, you can apply the silicone to the substrates. Silicone can now be applied to one side of the entire surface to be bonded. If it is a large area, set the silicone more generously, but not too thickly. You can spread it out using a spatula.

Curing time should be 4-6 hours. But leave for 24 hours for complete cure.

The Finish

Stormsure is a NON-Staining Silicone Adhesive and Sealant.

Click here to read more on how to use Stormsure Silicone as a sealant

The Stand Up Paddleboard Repair Kit is specifically tailored for the maintenance and repair of SUPs. This comprehensive kit contains 2x 5g tubes of Stormsure Flexible Repair Adhesive, a Tuff Tape strip, and two Tuff Tape patches, offering a complete solution for fixing punctures, tears, and abrasions on paddleboards, ensuring a strong, reliable, and lasting repair.

Kit Contents:

1. 2x 5g Tubes of Stormsure Flexible Repair Adhesive: These tubes of high-performance adhesive are perfect for creating a durable, waterproof bond on SUP materials, ideal for sealing small leaks and mending punctures.

2. 2x Tuff Tape Patches (75mm Diameter): Designed for larger areas of damage, these self-adhesive patches offer a quick and robust solution for repairing significant tears or cuts on the paddleboard.

3. 1x Tuff Tape Strip (15cm Long): A versatile, longer strip of Tuff Tape suitable for elongated damages or reinforcing seams and edges on the SUP.

Key Features:

1. Specially Formulated for SUPs: The adhesive and patches are developed to bond effectively with the materials used in stand-up paddleboards.

2. Waterproof and Durable: Ideal for water sports equipment, the repairs withstand exposure to water, UV light, and general wear and tear.

3. Simple and Efficient Application: The kit allows for easy, DIY repairs, enabling paddleboarders to quickly mend damages without professional assistance.

4. Comprehensive Repair Options: Offers both adhesive and patch solutions to cater to different types of damages on the paddleboard.

5. Compact and Portable: Small and lightweight, it's an essential part of any paddleboarding gear for emergency or routine repairs.

Benefits:

• Cost-Effective: Avoids the expense of professional repairs or purchasing a new SUP.
• Quick and Convenient Repairs: Ensures that your paddleboarding activities aren't interrupted by damage to your board.
• Strong and Long-Lasting Repairs: Offers peace of mind that the repair will hold up against regular use.
• Maintains SUP Performance: Keeps the paddleboard in optimal condition, ensuring safety and enjoyment on the water.

How to Use:

1. Clean and dry the damaged area on the paddleboard.
2. For small punctures, apply the adhesive directly. For larger tears or abrasions, use the Tuff Tape patch or strip over the adhesive.
3. Press down firmly to ensure a solid bond.
4. Allow the adhesive to fully cure for 24 - 48 hours (depending on conditions) before using the SUP.

The Stand Up Paddleboard Repair Kit is an indispensable tool for SUP enthusiasts, providing an all-in-one solution for maintaining and repairing their boards. Whether facing minor wear and tear or more significant damage, this kit ensures your paddleboard remains seaworthy and ready for your next adventure on the water.

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This nifty adhesive will enable you to make easy and durable repairs to rips, roles, leaks and split seams on wetsuit and drysuit material. 

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 5 minutes, it should be touch dry and you will be ready to go back in the water!

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual water sports enthusiasts as well as professional triathletes who want to stand out.

This kit contains all the components that you need to replace the socks on a drysuit. Full instructions are on the pack. Make a good quality water tight repair at a fraction of the cost of sending the suit away for repair.

Latex socks come in two types 2D and 3D. 2D socks are flat whereas 3D socks have a foot shape moulded in. An important difference is the dimension across the top which determines which type can be fitted to which suit. Measure the ankle of the suit where the new sock is to be fitted. If you measure this flat across and then double it you get the circumference. Ideally the suit should be 1-2cm bigger than the sock which allows the latex to slightly stretch which gives the best finish. If the sock is bigger than the suit you will end up with creases in the latex which will probably leak.

Stormsure 3D Latex Socks

High Quality Latex made in the UK

Size: Large

Top Sock: 133mm diameter

Bottom Sole length: 290mm

Height: 290mm

Stormoprene Adhesive

Stormoprene Hypalon Adhesive is a specially formulated 2-part poly-chloroprene based adhesive system for high-performance bonding of Hypalon and other natural and synthetic rubber surfaces that require high strength bonds for use in demanding applications.

Formulated for use in the manufacture and repair of RIBs, inflatable boats, liferafts, diving suits, wet suits and other marine and industrial applications that specify resistance to salt water, oil, fuels etc. 

Directions:

1. Cut off the damaged seal, leaving the part of the suit where the factory seal is attached to the fabric. The new seal will be glued over the old factory seal edge.

2. Slide the new seal into the factory edge and put an elastic band or bungee around the suit to keep it in place. Slide some silicone/wax paper under the cut off edge to keep glue from sticking to the seal, or you can put wax on the seal.

3. Clean the edge of the suit and the new seal edge with solvent (the side with the stripes is the inside.) Gently sand paper it to roughen the surface. Do not let the seal stick out too far, as the small end of the seal should not be stretched over it. It might cause the new seal to slide out of position.

4. Slide the seal on over the factory rubber area. You can put elastic bands around to keep the new seal from sliding.

5. Roll back the new seal so that the 2cm edge that was over the old suit is now facing up. Apply a thin layer of Stormoprene Contact Adhesive to each side. Wait 5 minutes and apply a second layer of adhesive to each side. Use a spatula or knife to apply the glue. When the glue is touch dry, roll the new latex seal right into place over the rubber part of the old seal. It bonds instantly. Press firmly over the glue area to ensure full adhesion.

6. Take your time.

It's all about Stormsure Flexible Repair Adhesive

The Stormsure Flexible Repair Adhesive Khaki (15g) is a versatile, high-strength adhesive designed for a wide array of repair needs. This clear adhesive is perfect for a multitude of applications, offering a flexible, waterproof, and durable bond. It's ideal for repairing items like outdoor gear, footwear, inflatable items, tents, and much more, ensuring a reliable and long-lasting fix. Especially khaki or brown items where the black adhesive can create an invisible repair. 

Key Features:

• Strong and Flexible Bond: Provides a robust bond that remains flexible once cured, ideal for materials that need to retain elasticity.
• Clear Formula: The adhesive dries clear, making it suitable for repairs where appearance is important, leaving a clean and unobtrusive finish.
• Waterproof and Durable: Once cured, the adhesive creates a waterproof seal, making it perfect for outdoor and water-related repairs.
• Multipurpose Use: Ideal for repairing a wide range of materials, including rubber, leather, PVC, neoprene, canvas, and various fabrics.
• Easy Application: The tube allows for precise application, making it simple to apply the right amount of adhesive exactly where it's needed.

Benefits:

• Versatile Repair Solution: Suitable for everything from patching a tent to fixing a shoe sole or mending an inflatable pool toy.
• Cost-Effective: Saves money by enabling easy repairs instead of needing to replace damaged items.
• Long-Lasting Repairs: Offers a durable solution that withstands wear and tear, as well as exposure to the elements.
• User-Friendly: Easy to use for both quick fixes and more complex repairs.

How to Use:

1. Ensure the surface to be repaired is clean and dry.
2. Apply the adhesive directly to the damaged area.
3. If necessary, press the two surfaces together and remove any excess adhesive.
4. Allow to cure for 24-48 hours (depending on conditions) for optimal strength.

The Stormsure Flexible Repair Adhesive Khaki (15g) is an essential tool for any repair kit, whether at home, in the workshop, or on the go. It's a go-to solution for a diverse range of repair tasks, ensuring that your gear and items remain functional and well-maintained, saving time and money in the long run.

Glue for repairing all types of water sports equipment and clothing

This very special adhesive glue is one of the few products that can repair leaks, cracks and rips on water sport inflatables, equipment, canoes, sailing, boats, swimming, diving, kayaks, and clothing and many more!
Repairs are permanent, strong, waterproof, flexible and resistant to abrasion (weather and water abrasion).

A perfect way to get you back into the water safely, Stormsure glue is the perfect solution. You can plug the hole or patch the tear with this excellent product.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS:
Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 24 hours.
TIPS:
Mix with Stormcure Accelerator to reduce cure time to approximately 1 hour. Ensure there is no air left in the tube before replacing cap.
Store partly-used tubes in a deep freezer.

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Special neoprene glue to repair your diving and swimming suit.

Neoprene Queen is an essential part of the maintenance kit for your wetsuit.

Its fast drying and resistance allows you to repair holes and tears in your neoprene wetsuit (surf, kitesurf, windsurf, etc) in just 20 minutes.
It is perfect for last minute repairs. Imagine, you are on the beach or next to a river and you have just damaged your wetsuit but still want to get back in the water. With Neoprene Queen, no need for patches, just apply the glue on the 2 edges of the tear, wait 2 min, then press the 2 edges together.

Neoprene Queen will quickly become an essential element for all casual water sports enthusiasts, Triathletes, Surfers, Swimmers, Divers, Kite Boarders, Body Boarders, Fishermen and many more!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This special adhesive will enable you to make easy and durable repairs to rips, tears, leaks and split seams on wetsuit and drysuit material.

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 20 minutes, it should be touch dry and you will be ready to go back in the water!

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This nifty adhesive will enable you to make easy and durable repairs to rips, roles, leaks and split seams on wetsuit and drysuit material. 

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 5 minutes, it should be touch dry and you will be ready to go back in the water!

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual water sports enthusiasts as well as professional triathletes who want to stand out.

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Special neoprene glue to repair your diving and swimming suit.

Neoprene Queen is an essential part of the maintenance kit for your wetsuit.

Its fast drying and resistance allows you to repair holes and tears in your neoprene wetsuit (surf, kitesurf, windsurf, etc) in just 20 minutes.
It is perfect for last minute repairs. Imagine, you are on the beach or next to a river and you have just damaged your wetsuit but still want to get back in the water. With Neoprene Queen, no need for patches, just apply the glue on the 2 edges of the tear, wait 2 min, then press the 2 edges together.

Neoprene Queen will quickly become an essential element for all casual water sports enthusiasts, Triathletes, Surfers, Swimmers, Divers, Kite Boarders, Body Boarders, Fishermen and many more!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This special adhesive will enable you to make easy and durable repairs to rips, tears, leaks and split seams on wetsuit and drysuit material.

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 20 minutes, it should be touch dry and you will be ready to go back in the water!

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Special neoprene glue to repair your diving and swimming suit.

Neoprene Queen is an essential part of the maintenance kit for your wetsuit.

Its fast drying and resistance allows you to repair holes and tears in your neoprene wetsuit (surf, kitesurf, windsurf, etc) in just 20 minutes.
It is perfect for last minute repairs. Imagine, you are on the beach or next to a river and you have just damaged your wetsuit but still want to get back in the water. With Neoprene Queen, no need for patches, just apply the glue on the 2 edges of the tear, wait 2 min, then press the 2 edges together.

Neoprene Queen will quickly become an essential element for all casual water sports enthusiasts, Triathletes, Surfers, Swimmers, Divers, Kite Boarders, Body Boarders, Fishermen and many more!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This special adhesive will enable you to make easy and durable repairs to rips, tears, leaks and split seams on wetsuit and drysuit material.

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 20 minutes, it should be touch dry and you will be ready to go back in the water!

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Special neoprene glue to repair your diving and swimming suit.

Neoprene Queen is an essential part of the maintenance kit for your wetsuit.

Its fast drying and resistance allows you to repair holes and tears in your neoprene wetsuit (surf, kitesurf, windsurf, etc) in just 20 minutes.
It is perfect for last minute repairs. Imagine, you are on the beach or next to a river and you have just damaged your wetsuit but still want to get back in the water. With Neoprene Queen, no need for patches, just apply the glue on the 2 edges of the tear, wait 2 min, then press the 2 edges together.

Neoprene Queen will quickly become an essential element for all casual water sports enthusiasts, Triathletes, Surfers, Swimmers, Divers, Kite Boarders, Body Boarders, Fishermen and many more!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This special adhesive will enable you to make easy and durable repairs to rips, tears, leaks and split seams on wetsuit and drysuit material.

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 20 minutes, it should be touch dry and you will be ready to go back in the water!

After much feedback from our customers we have now launched our NEW IMPROVED FORMULA for Neoprene Queen. We are delighted that this much improved adhesive formula will now work with all neoprene materials and now also with latex, pvc and many other materials too! It is now the complete adhesive solution for anything water sports!

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This nifty adhesive will enable you to make easy and durable repairs to rips, roles, leaks and split seams on wetsuit and drysuit material. 

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 5 minutes, it should be touch dry and you will be ready to go back in the water!

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual water sports enthusiasts as well as professional triathletes who want to stand out.

This kit contains all the components that you need to replace the bottleneck shaped wrist seal on a drysuit. Full instructions are on the pack. Make a good quality water tight repair at a fraction of the cost of sending the suit away for repair.

Stormsure Bottleneck Shaped Wrist Seal

High Quality Latex made in the UK

Size: Medium

Top Cone: 44mm diameter

Bottom Cone: 89mm diameter

Height: 120mm

Stormoprene Adhesive

Stormoprene Hypalon Adhesive is a specially formulated 2-part poly-chloroprene based adhesive system for high-performance bonding of Hypalon and other natural and synthetic rubber surfaces that require high strength bonds for use in demanding applications.

Formulated for use in the manufacture and repair of RIBs, inflatable boats, liferafts, diving suits, wet suits and other marine and industrial applications that specify resistance to salt water, oil, fuels etc. 

Directions:

1. Cut off the damaged seal, leaving the part of the suit where the factory seal is attached to the fabric. The new seal will be glued over the old factory seal edge.

2. Slide the new seal into the factory edge and put an elastic band or bungee around the suit to keep it in place. Slide some silicone/wax paper under the cut off edge to keep glue from sticking to the seal, or you can put wax on the seal.

3. Clean the edge of the suit and the new seal edge with solvent (the side with the stripes is the inside.) Gently sand paper it to roughen the surface. Do not let the seal stick out too far, as the small end of the seal should not be stretched over it. It might cause the new seal to slide out of position.

4. Slide the seal on over the factory rubber area. You can put elastic bands around to keep the new seal from sliding.

5. Roll back the new seal so that the 2cm edge that was over the old suit is now facing up. Apply a thin layer of Stormoprene Contact Adhesive to each side. Wait 5 minutes and apply a second layer of adhesive to each side. Use a spatula or knife to apply the glue. When the glue is touch dry, roll the new latex seal right into place over the rubber part of the old seal. It bonds instantly. Press firmly over the glue area to ensure full adhesion.

6. Take your time.

This kit contains all the components that you need to replace the Cone shaped wrist seal on a drysuit. Full instructions are on the pack. Make a good quality water tight repair at a fraction of the cost of sending the suit away for repair.

Stormsure Cone Shaped Wrist Seal

High Quality Latex made in the UK

Size: Medium

Top Cone: 38mm diameter

Bottom Cone: 89mm diameter

Height: 130mm

Stormoprene Adhesive

Stormoprene Hypalon Adhesive is a specially formulated 2-part poly-chloroprene based adhesive system for high-performance bonding of Hypalon and other natural and synthetic rubber surfaces that require high strength bonds for use in demanding applications.

Formulated for use in the manufacture and repair of RIBs, inflatable boats, liferafts, diving suits, wet suits and other marine and industrial applications that specify resistance to salt water, oil, fuels etc. 

Directions:

1. Cut off the damaged seal, leaving the part of the suit where the factory seal is attached to the fabric. The new seal will be glued over the old factory seal edge.

2. Slide the new seal into the factory edge and put an elastic band or bungee around the suit to keep it in place. Slide some silicone/wax paper under the cut off edge to keep glue from sticking to the seal, or you can put wax on the seal.

3. Clean the edge of the suit and the new seal edge with solvent (the side with the stripes is the inside.) Gently sand paper it to roughen the surface. Do not let the seal stick out too far, as the small end of the seal should not be stretched over it. It might cause the new seal to slide out of position.

4. Slide the seal on over the factory rubber area. You can put elastic bands around to keep the new seal from sliding.

5. Roll back the new seal so that the 2cm edge that was over the old suit is now facing up. Apply a thin layer of Stormoprene Contact Adhesive to each side. Wait 5 minutes and apply a second layer of adhesive to each side. Use a spatula or knife to apply the glue. When the glue is touch dry, roll the new latex seal right into place over the rubber part of the old seal. It bonds instantly. Press firmly over the glue area to ensure full adhesion.

6. Take your time.

This kit contains all the components that you need to replace the neck seal on a drysuit. Full instructions are on the pack. Make a good quality water tight repair at a fraction of the cost of sending the suit away for repair.

Stormsure Neck Seal

High Quality Latex made in the UK

Size: Medium

Top Cone: 89mm diameter

Bottom Cone: 254mm diameter

Stormoprene Adhesive

Stormoprene Hypalon Adhesive is a specially formulated 2-part poly-chloroprene based adhesive system for high-performance bonding of Hypalon and other natural and synthetic rubber surfaces that require high strength bonds for use in demanding applications.

Formulated for use in the manufacture and repair of RIBs, inflatable boats, liferafts, diving suits, wet suits and other marine and industrial applications that specify resistance to salt water, oil, fuels etc. 

Directions:

1. Cut off the damaged seal, leaving the part of the suit where the factory seal is attached to the fabric. The new seal will be glued over the old factory seal edge.

2. Slide the new seal into the factory edge and put an elastic band or bungee around the suit to keep it in place. Slide some silicone/wax paper under the cut off edge to keep glue from sticking to the seal, or you can put wax on the seal.

3. Clean the edge of the suit and the new seal edge with solvent (the side with the stripes is the inside.) Gently sand paper it to roughen the surface. Do not let the seal stick out too far, as the small end of the seal should not be stretched over it. It might cause the new seal to slide out of position.

4. Slide the seal on over the factory rubber area. You can put elastic bands around to keep the new seal from sliding.

5. Roll back the new seal so that the 2cm edge that was over the old suit is now facing up. Apply a thin layer of Stormoprene Contact Adhesive to each side. Wait 5 minutes and apply a second layer of adhesive to each side. Use a spatula or knife to apply the glue. When the glue is touch dry, roll the new latex seal right into place over the rubber part of the old seal. It bonds instantly. Press firmly over the glue area to ensure full adhesion.

6. Take your time.

Its premium quality Neoprene material and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use.

Often bought with Neoprene Queen Contact adhesive.

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual watersports enthusiasts as well as professional triathletes.

Its premium quality Neoprene material and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use.

Often bought with Neoprene Queen Contact adhesive.

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual watersports enthusiasts as well as professional triathletes.

Its premium quality Neoprene material and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use.

Often bought with Neoprene Queen Contact adhesive.

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual watersports enthusiasts as well as professional triathletes.

Stormsure ’TUFF Tape’ is a very strong, clear, self-adhesive, waterproof tape that is sold as individual pre-cut patches and strips of various shapes and sizes. TUFF Tape is made of a thin, but very tough, polyurethane film with a pressure sensitive adhesive and backing paper on the rear side. It has characteristics unlike many other tapes. It is waterproof and air tight. It is highly resistant to abrasion and very difficult to tear or puncture. It stretches and is elastic and it can withstand both heat and extreme cold without losing all its useful characteristics. TUFF Tape is very strong and can bind together items just by stretching the tape around the item and using the elasticity to pull the pieces tightly into place. When TUFF tape is applied to clothing it will go through regular washing machine cycles unaffected.

USES: Use TUFF Tape to quickly repair rips in waterproof clothing, ripped netting and fabrics, inflatable mattresses, canoes and RIBs, tents and awnings, sails and kites, waders, cracked buckets and other plastic containers, PVC curtain sides on trucks and warehouses.

DIRECTIONS: Ensure that the surface is clean and dry before using. Cut a suitable sized piece of TUFF Tape for your repair using good quality scissors or a sharp scalpel blade. Peel off the backing paper. Carefully position and then apply the TUFF Tape directly on top of the damage. Start at one edge and press the tape down gradually to avoid the entrapment of air bubbles. Once the TUFF Tape is in place rub it firmly with a smooth and hard object (such as the back of a spoon) to ensure the maximum adhesion to the substrate.